CATALOG SEARCH

(click to download the PDF)

 

PS-102
Sportsman .550 Big Block GP20 Armatures
$33.95

PS-104
.450 Magnum Topgun Armature Note your choice 43/44/54 wind
$70.25

PS-105
Drag Style S16D- .513 OD @ 45 degrees
$36.95

PS-106
X-12 Hemi - 40 degrees timing .510
$46.90

PS-106MM
MegaMaster GP12 Armature
$56.95

PS-107
Grp 20 Hemi - 35 degrees timing .510
$49.95

PS-107MM
MegaMaster G20 Armature
$70.00

PS-108
Drag H27- 46 degrees timing, available in .445 to .460 diameter. Specify when ordering.
$70.00

PS-109A
X-blank .665 long, .250 stacks,.014 laminations
$45.00 Net

PS-109A-007
X-blank .665 long, .250 stacks, .007 laminations
$45.00 Net

PS-109B
X-blank .750 long, .300 stacks,.014 laminations
$45.00 Net

PS-109B-007
X-blank .750 long, .300 stacks, .007 laminations
$45.00 Net

PS-110A
Mark 7 blank, .665 long, .250 stacks, .007 laminations
$45.00 Net

PS-110B
Mark 7 blank, .750 long, .300 stacks, .007 laminations
$45.00 Net

PS-111C
Capped Scale Armatures X-blank .007 or .014 laminations or Mark 7 .007
$45.00 Net

PS-121
THE BOSS 490 Armature This armature is specially wound on our .490 stack M-2 blank. It is a drop in fit for all D-can motors
$33.95

PS-2006
16D Replacement Balanced Armature (commutator trued)
$11.67

PS-2007
S16D Replacement Balanced Armature (commutator trued)
$11.67

PS-206
P15 International - available in diameters from .480 to 500, standard length .860
$45.05

PS-207
C12 - available in diameters from .480 to .500, lengths of .750 to .860, standard timing 34 degrees
$45.90

PS-2109
Econo ProStock (EPS) Armature
$25.50

PS-211
Group 27 available in diameters of .480 to .500, timing of 32, 35 or 40 degrees, standard length is .850
$70.00

PS-220
Group 7 X-blank
$45.00 Net

PS-220C
Group 7 X-blank
$45.00

PS-221
Group 7 Mark 7 blank
$45.00 Net

PS-221C
Group 7 Mark 7 blank
$45.00 Net

PS-3006
X12 Replacement Balanced Armature (commutator trued)
$13.50

PS-3007
Contender Replacement Balanced Armature (commutator trued)
$13.50

PS-4000
Euro MK1 Motor - 26,100 + rpm, 155/gm-cm, 280mA, standard with 45 degree springs. Designed for 1/32 and 1/24 Scale- Home, Club and Commercial Racing. CW or CCW rotation
$13.95

PS-4008
Replacement balanced armature for the PS-4002 (commutator trued and rebalanced)
$9.29

PS-4009
PD (Puppy Dog) American made replacement armature (requires modified endbell PS-4011 for comm clearance). CW Rotation
$26.50

PS-4009-CCW
PD (Puppy Dog) American made replacement armature (requires modified endbell PS-4011 for comm clearance). CCW Rotation
$26.50

PS-4010
BD (Big Dog) 55 turns of 30 gauge with 25 degrees timing American made replacement armature (requires modified endbell PS-4011 for comm clearance). CW Rotation
$26.50

PS-4010-CCW
BD (Big Dog) 55 turns of 30 gauge with 25 degrees timing American made replacement armature (requires modified endbell PS-4011 for comm clearance). CCW Rotation
$26.50

PS-4012
X12 with 38 degrees timing American made replacment armature (requires modifed endbell PS-4011 for comm clearance). CW Rotation
$29.50

PS-4012-CCW
X12 with 38 degrees timing American made replacment armature (requires modifed endbell PS-4011 for comm clearance). CCW Rotation
$29.50

PS-4016
Hawk Replacement Armatures
$29.50

PS-4022
Velociraptor VR 20 NEO Replacement Armature Machine wound G20 armature, .500 diameter, wound on our race proven Intruder blank. This armature is specially sized to fit the PS-4017 NEO Euro MK1 setup to provide the ideal airgap with no other modifications needed.
$42.95

PS-4023
Velociraptor VR eXtreme NEO Replacement Armature Machine wound, eXtreme wind armature, .500 diameter, wound on our race proven Intruder blank. This armature is specially sized to fit the PS- 4017 NEO Euro MK1 setup to provide the ideal airgap with no other modifications needed. This the fastest machine wound armature available for the PS-4017 NEO MK1 setup.
$42.95

PS-4024
Velociraptor VR Custom NEO Armature This is a custom hand wound all-out Topgun style armature featuring our EDM commutator, wound on our race proven Intruder blank. This armature is .500 standard diameter and is also available in .480 and .490 diameters for the custom motor builders as a special order. Standard wind is 25/25. Also available in 18/24.5, 15/24, 14/24, 14/23
$74.95

PS-4026
Velociraptor VR 12 NEO Replacement Armature Machine wound G12 armature , .500 diameter, wound on our race proven Intruder blank. This armature is specially sized to fit the PS-4017 NEO Euro MK1 setup to provide the ideal airgap with no other modifications needed.
$42.95

PS-700
S16D
$34.50

PS-700B
S16D .560
$34.50

PS-700C
S16C
$34.50

PS-700C-B
S16C .560
$34.45

PS-700S
Outlaw S16D .450 stacks .520
$34.50

PS-700S-B
Outlaw S16D .450 stacks .540
$34.5

PS-701
Box Stock X12 .513
$38.50

PS-701B
Box Stock X12 .540
$38.50

PS-701BD
Box Stock X12 .540 drill blank
$42.50

PS-701BI
Box Stock X12 .550, .555 or .560
$42.50

PS-701D
Box Stock X12 .513 with drill blank
$42.50

PS-701L
Box Stock X12 .514 to .518 diameter
$38.50

PS-702
USRA Spec 15 .513, only available with 38 degrees timing
$38.50

PS-702D
USRA Spec 15 .513, only available with 38 degrees timing, and drill blank
$42.50

PS-703
G20 .513
$42.50

PS-704
Super Wasp .513
$32.75

PS-704B
Super Wasp .540
$32.75

PS-704BI
Super Wast .550, .555 or .560
$32.75

PS-705
Contender .513
$31.25

PS-705B
Contender .540
$31.25

PS-705BI
Contender .550, .555 or .560
$31.25

PS-706
16D .518 balanced or unbalanced
$33.90

PS-706B
16D .560 balanced
$33.90

PS-707
Infinity replacement armature for PS-315 RTR 30Turn 26
$42.50

PS-708
G20 - available in diameters from .480 to .500, lengths of .900 to .935
$47.50

PS-710
Top Gun 18/24.5 - 18 degrees timing .510
$70.00

PS-712
Pro Outlaw Grp 20 Hemi .510
$49.95

PS-713
Top Gun Custom Winds. Specify when ordering.
$70.00

PS-715
Pro X-12 Armature
$46.90

PS-800
Group 27 .459 diameter, timing of 32, 35 or 40 degrees, standard length is .850
$70.00

PS-851
Group 7 .459 blank
$45.00 Net

PS-851C
Group 7 .459 Blank
$45.00 Net

PS-852
Group 7 Drag armature 21 degree timing, .445 diameter, .860 long and with our Edm commutator.
$85.98

PS-317-12
Perimeter Box Stock Chassis (4.330 long) - 2012/2013 version
$52.50

PS-318-08
Tripod Box Stock Chassis (4.370 long) - 2008/2009 version
$52.50

PS-319
USRA Spec 15 Chassis - each chassis has a serial number and should be registered with the USRA. A registration sheet is included with each chassis.
$52.50

PS-5000
SpeedFX C-Can Chassis
$21.95

PS-5001
SpeedFX D-Can Chassis
$21.95

PS-410
3/32 x 3/16 axle ball bearings, flanged and double shields (10 Balls)
$11.00 pr

PS-420
1/8 x 1/4 axle ball bearings, flanged & double shields (7 Balls)
$11.00 pr

PS-5000C
C-Can Center Section
$11.95

PS-5001C
D-Can Center Section
$11.95

PS-5002
Standard pans
$10.95

PS-5003
Medium pans
$10.95

PS-5004
Light pans
$10.95

PS-5010
Chassis Cotter Clips - 12
$3.00

PS-607
3/32 Drill Blank Axle - 6 (1.99 ea.)
$11.94

PS-610
Super Light Front Wheels
$1.85

PS-619
Lead Wire with Clips 6 per card.
$15.96

PS-620
Dragster leadwire with clips 16" long
$3.32

PS-621
Lead Wire - Bulk Pack of 3 feet
$3.00

PS-622
Lead Wire - Bulk Pack of 10 feet
$6.00

PS-624
Standard Lead Wire Clips .012 thick hard brass 6 pr.
$9.96

PS-625
Internal Lead Wire Clips .012 thick hard brass 6 pr.
$9.96

PS-671
Polymer Gears 64 Pitch (Bulk Pack) Same as above but bulk pack of 25 (3.00 ea.)
$78.75

PS-673
Polymer Gears 48 Pitch (Bulk Pack) Same as above but bulk pack of 25 (3.00 ea.)
$78.75

PS-675
Polymer Gears 72 Pitch (Bulk Pack) Same as above but bulk pack of 25 (4.25 ea)
$106.25

PS-680
Polymer Gears 64 Pitch - The tooth shape was computer designed for less friction. Will never spin on the hub. 35- red, 36T-yellow, 37T-silver, 38T-blue, 39T-violet, 40T-green - 6 per card
$20.40

PS-682
Polymer Gears 48 Pitch - Same as PS-670 except 48 pitch. 26T-pink 27T-white,28T-yellow, 29T-violet, 30T-green, 31T-blue, 32T-brown - 6 per card
$20.40

PS-684
Polymer Gears 72 Pitch 40-green, 41-yellow, 42-pink, 43-black, 44-brown - 6 per card
$36.00

PS-686
Polymer Gears 72 Pitch 15* angle, 42-pink, 43-black, 44-brown - 6 per card
$36.00

PS-101
Sportsman .550 Big Block GP20 Drag Motor
$47.50

PS-103
450 Magnum Topgun Motor Note your choice Quad or 6 Mag 43/44/54 wind
$150.95

PS-120
THE BOSS 490 Motor This motor has standard .570 airgap and comes with our PS-121 BOSS armature. The setup is blueprinted and copper harder is installed on the endbell. Add 14.00 for double ball bearings
$58.95

PS-2000
16D Balanced Motor
15.25

PS-2001
S16D Balanced Motor
$16.25

PS-2002
16D Balanced Motor - Double Security Sealed
$15.75

PS-2003
S16D Balanced Motor - Double Security Sealed
$16.98

PS-2101
Motor with S16D Balanced Armature
$32.75

PS-2101S
Motor with S16D Balanced Armature - sealed and engraved
$33.75

PS-2102
Motor with 16D Balanced Armature
$32.75

PS-2102S
Motor with 16D Balanced Armature - sealed and engraved
$33.25

PS-2103
Motor with PS-700 S16D Unbalanced Armature
$50.25

PS-2104
Motor with PS-700 S16D Balanced Armature
$50.25

PS-2105
Motor with PS-700S Outlaw S16D Balanced Armature
$50.25

PS-2106
Motor with PS-706 16D Unbalanced Armature
$50.25

PS-2107
Motor with PS-706 16D Balanced Armature
$50.25

PS-2108
Blueprinted S16D Econo ProStock (EPS) Motor
$56.25

PS-2108A
Blueprinted S16D Econo ProStock Motor with PS-105 Drag S16D armature
$63.95

PS-2110
Motor with .560 Balanced Armature.Your choice of (A) S16D (B) Outlaw S16D (C) 16D
$55.00

PS-3000
X12 Balanced Motor- Black Endbell
$32.00

PS-3000S
X12 Balanced Motor - Black Endbell - Double Security Sealed
$33.00

PS-3001
Contender Balanced Motor - Natural Endbell
$32.00

PS-3001S
Contender Balanced Motor - Natural Endbell - Double Security Sealed
$33.00

PS-4001
Euro MK1 Motor - 37,000 + rpm, 160/gm-cm, 300mA, standard with 60 degree springs. Designed for 1/32 and 1/24 Scale - Home, Club and Commercial Racing. CW or CCW rotation
$13.95

PS-4002
Euro MK 1 Motor - 47,000 + rpm, 160/gm-cm, 950mA, standard with 90 degree springs. Designed for 1/32 and 1/24 Scale - Home, Club and Commercial Racing.
$13.95

PS-4002-12
Euro MK 1 Motor with American made X12 armature 38* CW Rotation
$46.00

PS-4002-12-CCW
Euro MK 1 Motor with American made X12 armature 38* CCW Rotation
$46.00

PS-4002-12CPR
Euro MK 1 Motor with American made X12 armature 38* CW Rotation, assembled with copper hardware Add $7.00 for single or $14.00 for double Ball bearings.
$51.95

PS-4002-R
Raptor Euro MK-1 Motor with American Made Hawk Armature CW Rotation
$42.00

PS-4002-R-CCW
Raptor Euro MK-1 Motor with American Made Hawk Armature CCW Rotation
$42.00

PS-4002B
Euro MK1 Motor with American made PD (Puppy Dog) armature as used in retro can am racing, with 4 can screws and double seal. This motor runs correctly CW Rotation
$45.00

PS-4002B-B
Euro MK1 Motor with American made PD (Puppy Dog) armature and can ball bearing, as used in retro can am racing, with 4 can screws and double seal. This motor runs correctly CW Rotation
$51.00

PS-4002B-BCCW
Euro MK1 Motor with American made PD (Puppy Dog) armature and can ball bearing, as used in retro can am racing, with 4 can screws and double seal. This motor runs correctly CCW Rotation.
$51.00

PS-4002B-CCW
Euro MK1 Motor with American made PD (Puppy Dog) armature as used in retro can am racing, with 4 can screws and double seal. This motor runs correctly CCW Rotation
$45.00

PS-4002C
Euro MK1 Motor with American made BD (Big Dog) armature CW Rotation.
$43.00

PS-4002C-CCW
Euro MK1 Motor with American made BD (Big Dog) armature CCW Rotation.
$43.00

PS-4002FK

We are excited and pleased to release our PS-4002FK motor.

Everyone has been waiting for an FK motor for sealed motor racing and Retro racing with a combination of tamper proof endbell can and replaceable brushes with the same specs that everyone is using now.

This motor is based on our FK-MK1 series of motors and features poly/neo magnets, 65 turns of 30 gauge wire, 15 deg timing, with clockwise rotation from the can side. The shafts are long enough for Comm Coolers and endbell drive if desired.

The enbells are glued on, the tabs are crimped, they are drilled and tapped, screws installed can to endbell and our seals are used. These are the same specs as the current FK motors offered by other companies in this market place.

PS-4002FK Euro MK1 Motor, 65 turns of 30, 15 deg timing, poly neo magnets, glued on endbells, crimped tabs, drilled and tapped with screws installed can to endbell and then covered by our SpeedFX Seals. $13.95

Proslot recommends gearing the PS-4002FK with a overall gear ratio of 3.25 to 3.75 or to a "roll out" ratio of 4.25 to 4.50

$13.95

PS-4019
Velociraptor VR 12 NEO motor This motor uses the new PS-4017 Neo Euro MK1 setup with a specially made .500 diameter VR12 machine wound armature on our race proven Intruder blank and includes Goldust brushes. This motor was built for the new wave of NEO F/C racing. Our testing using an 85 gram hardbody test car netted .720 ETs @ 70+ MPH. Recommended starting gear ratio 14/52. Add $14.00 for double ball bearings.
$63.95

PS-4020
Velociraptor VR 20 NEO motor This motor uses the new PS-4017 NEO Euro MK1 setup with a specially made .500 diameter VR20 machine wound armature on our race proven Intruder blank and includes Goldust brushes. This motor was built for the Serious bracket racer and would be great for a NEO G20 F/C class. Our testing using an 85 gram hardbody test car netted .640 ETs @ 80+ MPH. Recommended starting gear ratio 14/54. Add $14.00 for double ball bearings
$69.95

PS-4021
Velociraptor VR eXtreme NEO motor This motor uses the new PS-4017 NEO Euro MK1 setup with a specially made .500 diameter VR eXtreme machine wound armature on our race proven Intruder blank and includes Goldust brushes. This motor was built for the Ultimate bracket racer and Outlaw NEW class racer. Our testing using an 85 gram hardbody test car netted .590 ETs @ 90+ MPH. This motor has no equal in performance for the money. Recommended starting gear ration 14/54. Add $14.00 for double ball bearings.
$73.95

PS-4025
Velociraptor VR Open NEO motor This motor uses the new PS-4017 NEO Euro MK1 setup with a specially made .500 diameter custom hand wound all-out Topgun style armature featuring our EDM commutator, wound on our race proven Intruder blank. Standard wind 18/24.5 and double ball bearings. Also available in 25/25, 15/24, 14/24 14/23
$136.95

PS-723
Group 12 Motor
$57.75

PS-723D
Group 12 Motor with drill blank
$63.75

PS-725
Dragmaster "SPEC" Motor This motor was Dyno designed to fall between the PS-101 and PS-748-20 in performance but on a budget. This motor is based on our race proven "SRS" set-up and has an all new SPEC armature featuring a softer launch than the Quad 20 but will still pull 110,000+ rpm at the topend! This motor comes with Goldust brushes and is double security sealed to prevent tampering.
$58.95

PS-728
USRA Spec 15 Motor, 38 degrees
$56.75

PS-728A
USRA Spec 15 Motor with Drill blank, 38 degrees
$61.75

PS-729
Contender Motor - unbalanced
$56.13

PS-729B
Contender Motor - balanced
$56.13

PS-730
Group 20 Motor
$58.95

PS-732
Super Wasp Motor
$56.13

PS-733
Dragmaster Competition series Purple Dot Top Gun Motor Same as PS-748-12 but with our PS-710 Topgun 84.5 armature. Add BB to the part number and $14.00 to the following price for ball bearings.
$137.95

PS-733BBMM
MegaMaster Topgun ball bearing Motor
$155.95

PS-733MM
MegaMaster Topgun Motor
$140.95

PS-734
Super 16C Motor
$54.95

PS-738-D
The Dragmaster Sportsman G20 Motor This motor includes our race proven Dragmaster can and endbell 2/copper hardware, Mega III FX magnets installed with spring clips and a PS-703 .513 G20 armature*. This motor is approved by the UDA for competition.
$65.95

PS-738-D-12
The Dragmaster Sportsman X-12 Motor This motor includes our race proven Dragmaster can and endbell 2/copper hardware, Mega III FX magnets installed with spring clips and a PS-106 .513 X-12 40* armature*. This motor is approved by the UDA for competition.
$63.95

PS-739-D
Dragmaster Sportsman SSA Spec Motor This motor includes our race proven Dragmaster can and endbell, Mega III FX magnets installed with spring clips and a Specially tagged .513 G20 armature with 40 degrees timing*. This armature is tagged "SSA20", dyed a special color and is only available in this motor, not separately. The motor screws are ground and the can is sealed to prevent tampering. Goldust Brushes are installed. This motor is approved by the UDA for competition.
$65.95

PS-740
Group 12 Motor
$65.95

PS-740PRO
Group 12 motor with epoxied magnets honed to .529 to .530.
$85.20

PS-741
Super Wasp Motor
$62.95

PS-742
Group 20 Motor
$67.95

PS-743
Quad 20 Motor
$105.95

PS-748-12
Dragmaster Competition series Purple Dot Drag 12 Motor This is a professionally built complete motor by Rodger Chiechi. It features our Dragmaster Competition series Purple Dot setup assembled with a PS-106 Hemi Drag 12 (custom timing available), modified Goldust brushes and shunts. This motor is completely blueprinted and broken in ready for installation into your car. Standard with bushings and available with high quality ball bearings. Add BB to the part number and $14.00 to the following price for ball bearings.
$111.95

PS-748-12MM
MegaMaster GP12 Motor
$127.95

PS-748-12S
DragMaster GP12 with 6-Mags
$115.95

PS-748-20
Dragmaster Competition series Purple Dot Drag 20 Motor Same as PS-748-12 but with our PS-107 Hemi Drag 20 armature. Add BB to the part number and $14.00 to the following price for ball bearings.
$116.95

PS-748-20-BBMM
MegaMaster GP20 ball bearing Motor
$145.95

PS-748-20MM
MegaMaster GP20 Motor
$132.95

PS-748-20S
DragMaster G20 with 6-Mags
$123.95

PS-748-20S-BB
DragMaster G20 with 6-Mags and ball bearings
$135.95

PS-760PRO
Blueprinted motor with epoxied magnets honed to ~.555 with your choice of (A) Contender, (B) Super Wasp, (C) S16C, (D) X12 - .540 Diameter
$92.50

PS-2005
16D/S16D Motor Can
$5.08

PS-2008
Replacement endbell
$2.55

PS-2009
Replacement assembled endbell
$4.59

PS-2010
Brush Hood and Heatsink Set
$4.50

PS-2011
Alloy Spring Cups (1 pr.)
$1.53

PS-2012
Endbell assembly screws (12 pcs.)
$2.14

PS-2013
Motor Springs -double overhead (6 pr.)
$6.12

PS-2014
Motor Brushes (6 pr.)
$9.60

PS-2015
2 X 5 Can & Endbell Oilites (6 pcs.)
$3.60

PS-2016
Matched Magnets (1 pr.)
$8.00

PS-400
2 x 5 can/endbell ball bearing, unflanged & unshielded - for Cobalt racing (7 Balls)
$7.00 ea

PS-401
2 x 5 endbell ball bearing, flanged and double shields -perfect for c-can endbells (7 Balls)
$7.00 ea

PS-4011
Replacement endbell modified for commutator clearance with American made armatures
$6.50

PS-4013-45
Replacement Springs 45 degrees
(6 pair/cd $1.00 ea.) $6.00

PS-4013-60
Replacement Springs 60 degrees
(6 pair/cd $1.00 ea.) $6.00

PS-4013-90
Replacement Springs 90 degrees
(6 pair/cd $1.00 ea.) $6.00

PS-4014
Replacement Motor Brushes
(6 pair/cd $1.60 ea.) $9.60

PS-4018
Velociraptor NEO magnets They are made to the same dimensions as our OEM Euro MK1 ceramic magnet. This means that they install in our standard Euro MK1 can with the stock magnet retaining clips and a drop of super glue. No epoxy or special tools neede
$19.95

PS-402
x 5 can ball bearing, flanged & double shields. Perfect for c-cans or Grp 7 cans (7 Balls)
$7.00 ea

PS-430
2 x 6 can/endbell ball bearing, flanged & double shields - for Mura or Parma motors (6 Balls)
$7.00 ea

PS-613
Silver Shunt Wire - 6 (1.25 ea.)
$7.50

PS-614
Silver Shunt Wire - Bulk Pack of 10 feet
$10.00

PS-618
Assembled Endbell - undrilled
$10.95

PS-618EURO
Euro Endbell complete undrilled This endbell is assembled with our copper hardware, aligned & modified for comm clearance on our Euro motors. Will fit all Euro & Neo ProSlot motors
$11.95

PS-618EURO-BB
Euro Endbell complete undrilled with Ball Bearing This endbell is assembled with our copper hardware, aligned & modified for comm clearance on our Euro motors. Will fit all Euro & Neo ProSlot motors
$17.50

PS-618FX
FX Endbell Complete undrilled This endbell is assembled with our copper hardware & aligned. This is the same endbell that comes on the THE BOSS 490 motor.
$10.95

PS-618FX-BB
FX Endbell Complete undrilled with Ball Bearing This endbell is assembled with our copper hardware & aligned. This is the same endbell that comes on the THE BOSS 490 motor.
$17.50

PS-623
Production Motor Brushes 6 pair (1.60 pr)
$9.60

PS-640
Magnet Clips for C-can 12 (.22 ea.)
$2.64

PS-641
Brush Hood & Heat Sink set
$3.98

PS-642
Hardware set complete -includes hardware, oilite, spring cups and screws
$6.50

PS-643
Complete Endbell Kit - includes endbell, hardware, spring cups, oilite and screws
$10.00

PS-711
Endbell with oilite bushing
$4.35

PS-714 Pro-SRS
Blueprinted C-can - straightened perfectly
$11.95

PS-714 Pro-VIP
Blueprined C-can - straightened perfectly
$11.95

PS-716
2 x 5 oilites 12 (.60 ea.)
$7.80

PS-717
Set of 8 (.30 ea.) self starting T5 Torx can and endbell screws
2.40

PS-717B
Bulk pack of 50 (.25 ea.) self starting T5 Torx can and endbell screws
$12.50

PS-722
Alloy Spring Cups 24 (1.50 pr.)
$18.00

PS-724
Armature Spacer Kit - Includes 2 phenolic and 8 brass motor spacers (.12 ea.)
$1.20

PS-726
Phenolic Motor Washers (package of 10)
$2.00

PS-747
Dragmaster C-can This C-can was designed from the ground up strictly for Drag Racing.
$13.95

PS-747-B Dragmaster C-can
Re-Sized for our thicker magnets
$16.95

PS-900
Goldust Pro Motor Brushes 6 pair (3.50 pr.)
$21.00

PS-901
Goldust Pro Motor Brushes Bulk Pack 50 pair (3.15 pr.)
$162.50

PS-903
Goldust Pro Vertical Motor Brushes 6 pair (4.00 pr.)
$24.00

PS-904
Goldust Pro Motor Brushes -shortened to fit Euro MK1 Motors 6 pair (4.50 pr.)
$27.00

PS-905
SMQ Single Magnet Quads - perform similar to a quad magnet
$9.50

PS-906
SMQ Matched Magnets
$13.50

PS-909
Purple dot Dragmaster Quad Magnets This magnet has been in development for over one year and is now ready. This is a special new type of ceramic material that has more gauss and higher coercive force. These magnets are assembled with special orientation to give unbelievable mid-range torque and RPM. They are stronger than .190/.200 thick magnets but are only .170 thick for easier motor assembly.
$35.95

PS-909S
MegaMaster 6-Mags (Magnets Only)
$35.95

PS-912
MEGA III Matched Blue Dot Magnets - same as our PS-908 only .450 long
$13.00

PS-913
Cobalt Magnets for C-12 racing. .450 tall x .360 long x .065 thick
$53.95

PS-2004
16D/S16D Motor Setup
$14.90

PS-2100
Setup with Matched Magnets
$19.50

PS-2100-B
Setup with Matched Magnets and sized to fit .560 diameter armatures
$22.40

PS-4017
Velociraptor NEO setup This setup has standard .540 airgap and comes with our PS-4011 modified endbell. It accepts any of our Euro armatures. This is the most powerful Euro MK1 setup currently made, gaussing 1800 points and producing incredible torque. Add $14.00 for double ball bearing
$42.00

PS-718
Dragmaster Competition series Purple Dot Setup with Oilites This is a professionally built setup by Rodger Chiechi. It features our Dragmaster C-can sized and aligned with our new Purple Dot Quad Magnets. They are matched, epoxied in place and honed to .520. This setup is completely blueprinted and ready for your choice of armatures.
$66.95

PS-718MM
MegaMaster 6-mag Busing Setup
$69.95

PS-719
Dragmaster Competition series Purple Dot Setup with Ball Bearings Same as PS-718 but with high quality ball bearings
$83.95

PS-719MM
MegaMaster 6-mag ball bearing Setup
$86.95

PS-737-D
The Dragmaster Sportsman Setup This setup includes our race proven Dragmaster can and endbell w/copper hardware, Mega II FX magnets installed with spring clips. This setup is approved by the UDA for competition
$33.95

PS-749SRS
C-can Setup kit (without magnets)
$19.00

PS-749VIP
C-can Setup kit (without magnets)
$19.00

PS-750SRS
C-can setup with our Mega III magnets
$30.00

PS-750VIP
C-can setup with our Mega III magnets
$30.00

PS-751
Group -12 Pro C-Can Blueprinted Setup
$51.95

PS-751B
Group -12 Pro C-Can Blueprinted Setup .555
$53.95

PS-314
RTR - features your choice of PS-317-12, PS-318-08 PS-319 or PS-319 chassis - available with the one of the below motors:

PS-314
PS-723 Group 12
$150

PS-314
PS-729 Contender
$150.00

PS-314
PS-730 Group 20
$150.00

PS-314
PS-732 Super Wasp
$150.00

PS-314R
Rolling car ready for your favorite motor, features your choice of PS-317-06, PS-318-04, PS-317-08, PS- 318-08 or PS-319 chassis
$109.00

PS-315
RTR with your choice of our chassis - Comes with a 30T/26 armature in a C-can with Mega II magnets, ball bearings and shunted Goldust Brushes
$180.50

 

CATALOG SEARCH